CFW-9 Five-Position Filter Wheel Seen here attached to an ST camera body.  The CFW-9 makes it possible to automatically take color images with LRGB filters.  Add an H-alpha filter for emission nebula, or perform photometric measurements with UBVRI filters.  Add an extra carousel and do both by switching entire filter sets.  The CFW-9 is available with or without filters.  The CFW-9 gets its power and control commands from the camera and is designed to match the ST-7/8/9/10/2000 body style in size and shape.
More info...   Part # CFW-9

CFW10 Ten-Position Filter Wheel
Also seen here attached to an ST camera for comparison.  The CFW10 allows you to carry a large array of filters in one filter wheel without having to change carousels.  LRGB+Clear filters for color imaging can be installed along with several narrow band filters such as H-alpha, O[III] and S[II], or a complete color plus photometric set.  The CFW10 adds only 0.56" of backfocus to SBIG cameras and can be used with camera lens adapters.  A stand-alone model, controlled via a computer's serial port, is available for other cameras. More info...
Part # CFW-10

LRGBC, UBVRI and Narrowband Filters
Red, Green, Blue, plus Clear and Luminance filters for color imaging are available in several varieties.  Our standard set suppresses light pollution while giving an excellent balance for all ST cameras.  Astrodon filters are parfocal with other Astrodon narrowband filters and offer 1:1:1 exposure ratios.  H-alpha, O[III] and S[II] filters are available for narrow band imaging of emission nebula.  UBVRI filters are available for photometric studies.   More info... 

AO-8 Adaptive Optics
Get the last bit of resolution from your system.  The AO-8 uses the built-in tracking CCD of an ST-7/8/9/10/2000 dual sensor camera to monitor the jitter of a guide star and make appropriate tilt-tip corrections to the image at up to 10Hz using a moveable diagonal mirror.  Local and low order atmospheric effects, telescope vibration and drive error are reduced or eliminated resulting in a sharper image.   More info... 
Part # AO-8

SGS Self-Guiding Spectrograph
The SGS utilizes the guiding CCD in the ST-7/8/9/10/2000 cameras to hold the object being measured on the narrow entrance slit for an extended period of time.   The full bandwidth is displayed on an ST-7 sized CCD.  For convenience, other self-guiding ST series cameras can also be used although there is no benefit to using a larger camera than the ST-7XME.  Dispersion with the high resolution grating is approximately 1 Angstrom per pixel at 9u.   More info...  Part # SGS

DSS-7 Deep Space Spectrograph
The DSS-7 is a lower cost alternative to the SGS.  The DSS-7 is actually more sensitive than the SGS making it excellent for Deep Space objects.  It does not self-guide and it has slightly lower resolution than the SGS.  It is optimized for popular Schmidt-Cassegrain telescopes but can be used on any system with an F/10 focal ratio.  It is ideal for deep space objects such as galaxies and nebula.  More info...    Part # DSS-7

Port Splitter
The port splitter attaches to the 9-pin "AO/CFW/SCOPE" port on an ST-7/8/9/10/2000 camera and gives you three 9-pin ports for attaching a variety of accessories such as a CFW8A, AO-7 and Relay Adapter at the same time.  An additional RJ11 relay output port is also provided and four red LEDs indicate relay activity.   The port splitter should be used to replace the temporary ribbon type Dual Relay Cable for more robust connections.  More info...     Part # MS-PORTSPLITTER

Dual Relay Cable
This ribbon type extension cable with additional ports is also supplied with an AO-7 so that an "ST" series camera can control a CFW8A, telescope drive and AO-7 all at the same time.  This cable is provided with every AO-7 as a convenience, however for permanent use the more robust Port Splitter accessory should be used. Part # 50705

ST-7RC Adapter Plug
This adapter is supplied with all "ST" series cameras.  It plugs into the 9 pin "AO/CFW/SCOPE" port on an ST-7/8/9/10/2000 camera and accepts an RJ-11 to RJ-11 Tracking Cable that connects the camera to your telescope drive's autoguider ("CCD") port.  This adapter plug is not required when using a CFW8A.  Part # 50706

Tracking Cable

This replacement 6-pin RJ-11 to RJ-11 cable connects the camera to the autoguider ("CCD") port of your telescope drive.  It is supplied with all "ST" series cameras.  Part # 50711

Desiccant Plug and "Dummy" Desiccant Plug
Every "ST" series camera is supplied with a desiccant plug installed in the camera and a spare "dummy" that is used to plug the CCD chamber while baking the actual desiccant plug.  Both are available as replacement parts if lost. 
Desiccant Plug Part # MS-DESICCANTST
Dummy Plug Part # 50141

Extra Nosepiece:  1.25" and 2"
These T-thread nosepieces screw into the female t-threads on ST cameras.   All ST cameras include at least one nosepiece.  Each nosepiece is threaded to accept filters and notched for extra security in the event the retaining screw comes loose slightly during the night.  For a more solid connection to Schmidt-Cassegrain scopes, we also offer the SCT to T-thread Visual Back (see below).
1.25" Nopsepiece Part # 51516
2" Nopsepiece Part  # 50146

SCT to T-thread Visual Back
For a more secure attachment of your camera to a Schmidt-Cassegrain telescope (or any scope using typical SCT threads) replace your nosepiece with this adapter.  One end screws into the female t-threads on the front of the camera or filter wheel, and the other end screws onto the rear cell threads typically found on most commercial Schmidt-Cassegrain telescopes.  A matching hard plastic dust cap screws over the t-thread end if the camera is removed for any period of time.
Part # 50702

Quick Disconnect
The Quick Disconnect accessory lets you quickly remove the camera from the telescope, replace it with an eyepiece, and then return the camera to the telescope all without losing focus or position.  It also lets you easily rotate the camera without losing focus.  It is designed for use with an SCT.   More info...  Part # MS-QUICK DISCON

CFW8A to AO-7 Adapter Plate
This adapter provides a solid direct connection of the AO-7 Adaptive Optics Device to the CFW8A filter wheel when the filter wheel is also hard mounted to the camera.   The entire train of Camera-CFW-AO becomes one unit.  Previously the AO-7 had to be attached using a male-to-male thread adapter that screwed into the CFW8A and AO-7, but could also add flexure or unwanted rotation if the parts became loose for any reason.    Part # MS-AO-8 ADAPTER

Replacement "D" Block and T-thread Ring
This block with adjustable inner t-thread ring is a standard part on ST-7/8/9/10/2000 cameras.  It can be removed for direct connection of the CFW8A or CFW10 filter wheel.
D-block Part # 50134
T-thread ring Part # 50147

Male-to-Male T-thread adapter
This adapter is also threaded internally for 1/25" filter cells, so it can be used to hold a single filter when attached to the front of the camera.
Part # 50704

Water Pump and Tubing (110VAC)
This 110VAC (only) submersible water pump may be used with any ST-7/8/9/10/2000 camera equipped with the water circulation heat exchanger.  Most models have this feature, except for some of the "I" models where it is an option.  Water circulation results in a greater cooling delta from ambient and is desirable in areas where it stays very warm at night.   Part # MS-ECP ONLY

Water Pump and Tubing (12VDC)
This 12VDC submersible water pump was added as an accessory for the larger STL series cameras.  However, if you are operating an ST-7/8/9/10/2000 camera in the field or any place where there is no convenient 110VAC supply, then it may be adapted for use with an ST series camera by using two pieces of step down tubing from the camera to the smaller tubing supplied with the 12VDC pump.  A 110VAC adapter (below) can be added for dual use.
Part # MS-WATER STL

110VAC to 12VDC power supply for 12V Water Pump
This 110VAC to 12VDC supply is may be used to power the 12VDC pump when 110VAC is available.  It is the same power supply that we use with the ST-402ME camera.
Part # 51686

90-240VAC Universal Power Supply
The universal power supply provides the required 5VDC and 12VDC to the camera from typical line voltages found around the world.  It has an on/off switch and green LED showing power is on to the camera.  A separate cord is available with regional plug for N. America and Europe / Asia.  This is the supply that is included with all current models of ST-7/8/9/10/2000 cameras.  It is compatible with all all past models as well.  Part # MS-PWR ST

12VDC Power Supply
This optional power supply converts 12VDC from a battery to the 5VDC and 12VDC required by the camera.  It is for operating your ST-7/8/9/10/2000 camera from a battery in the field, or anywhere there is no convenient AC power.  Part # 50388

Power Supply Extension Cable
This cable extends the cord from the power "brick" to the camera by approximately 8 feet (~2.44m).  The standard cable that comes with the power supply is about 6 feet (~1.83m) long so this heavy-duty extension cable brings the total length to about 14 feet (~4.27m).  It is custom made with heavy gauge conductor for minimum voltage loss.  The wire bundle is contained in a braided shell for added flexibility.
More info... 
Part # 51726

Accessory Test Lens
This inexpensive test lens allows the user to become familiar with CCD camera operation and software in the daytime.  The lens is a modest double convex plastic lens with a focal length of 25 mm and an aperture of 1.5 mm (F/16), in a metal housing with a T-thread on the outside. It is very handy for capturing images during daytime when testing the camera or learning the software.  Simply unscrew the nosepiece and screw this lens in place.     More info...
Part # MS-TEST LENS

Camera Lens Adapter
This adapter mates the ST-7/8/9/10/2000 cameras with popular 35mm camera lenses for wide field imaging. Adapters are available for Canon FD, or Nikon.  Note: Canon FD lenses are manual only.  The CLA-7 cannot be used with a filter wheel, but it can be used with the male-to-male t-thread adapter in place of the threaded barrel to hold a 1.25" filter behind the camera lens.  This can be useful for taking wide field H-alpha images, for example.  Part # CLA-7

Relay Adapter
The relay adapter box converts the ST-7/8/9/10/2000 electronic relays to mechanical relays.  Most commercially available mounts such as those from Software Bisque, AP, Meade and Celestron do not require mechanical relays, but others, such as the classic Losmandy G-11 do require some other form of electrical isolation between the camera and the mount.  If you are not sure, check with your mount manufacturer.  A special camera to adapter box cable (not shown) is provides the 12VDC needed to operate the relays.  Part # MS-RELAYCONNECT

Pelican Carrying Case with Custom Cut Foam
This case includes the custom cut foam (above) for your ST series camera and accessories.  It will hold an ST-7/8/9/10/2000 camera with or without a CFW10 filter wheel attached.  The case is waterproof, dustproof, and crushproof and comes with a lifetime guarantee from Pelican.  It is included as a standard accessory for current ST series cameras except for some "I" models.  It can be ordered separately for "I" cameras and older ST-7/8/9/10/2000 models.  More info...  
Part # MS-CASE ST

TheSky Version 5, Level II is distributed with SBIG cameras at no additional charge.  This is a full working demo version of the program.  Software Bisque offers a discount on upgrades to the latest version 6 at their web site http://www.bisque.com   Save $10 to $30 depending on the package you choose or keep the demo version and run it as long as you like.  It contains full version 5 capability with telescope control for many popular commercial goto scopes. Part #  

A discount certificate is included with most models of SBIG cameras for Maxim DL/CCD.  Maxim contains full SBIG camera control, including the ability to run 2 USB cameras at the same time, STV control and autoguiding through a series of exposures.  The certificate entitles the purchaser to obtain this popular camera control and image processing program for $50 off the current list price when purchased directly from SBIG.  Upgrades are available from Diffraction, Ltd.    Part #  

A discount certificate is included with all models of SBIG cameras for Ron Wodaski's popular book: The New CCD Astronomy.  This book covers all the basics you need to know to get started in CCD imaging.  But it is more than a beginner's book.  It contains a wealth of information on image processing and tips for getting the most from you camera.   Keep it as a reference book. The certificate if for $10 off the list price when purchased directly from SBIG.   More info...      Part #   

Microproject's Equinox program for Macintosh is a planetarium program, including full camera control for SBIG USB cameras.  SBIG will provide a free copy of EquinoX for Macintosh on request to any new camera purchaser who wants to use a Mac OS-X system to control his or her camera.  Send us a copy of your camera purchase invoice and we will send you EquinoX at no charge.   More info...      Part #